NTC temperatuuriandur koos Overmolding terminali ühendusliiniga

NTC temperatuurianduri sond koos ülevormimispistikuga (JST, Molex, RJ11, RJ12, RJ45, RJ50, XH, SM, PH, Lennunduspistik, klemmiplokid, 5557, Kiire terminal, heli pesa, jne). Anduri pea on valmistatud TPE materjalist, millel on hea nakkuvus ja tihendus. The sensor of Waterproof TPE plastic overmolding NTC thermistor is a kind of waterproof sensor solution. Anduri pea on valmistatud TPE materjalist, millel on hea nakkuvus ja tihendus. Softness and flexibility make this product widely used in a variety of applications.

The flexible and wide temperature range cable makes this type of probe particularly advantageous for cold detection applications.

The specifications of the sensor and the length of the cable can be customized according to requirements.

Waterproof NTC sensor TPE Overmolding water temperature measurement

TPE üleliistud 10K 3950 veepaagi temperatuurianduri kaabel 6,35 mm helipistikuga

Roostevabast terasest NTC andur koos TPE Overmolding pistikuga

Subject	Spetsifikatsioon	More options
Sensor	NTC 10KΩ	NTC 10K, NTC 50KΩ, NTC 100KΩ, PT100, PT1000, DS18B20, jne.
Kaabel	TPE cable	PVC cable, PU cable, silikoonkaabel, jne.
Ühendus	Nothing	JST, Molex, RJ11, RJ12, RJ45, RJ50, XH, SM, PH, Lennunduspistik, klemmiplokid, 5557, Kiire terminal, heli pesa, jne.
Precision	1%	1,5%, 2%, 2,5%, 3%, jne.
IP class	IP68	IP65, IP66, IP68, jne.

Waterproof NTC, PT100, DS18B20 temperature sensors can be used in many places, such as soil temperature detection, hot water tank temperature control, jne. The waterproof temperature sensor is a TPE Plastic Overmolding temperature sensor. This sensor can play a great role in measuring the temperature at a distance and in a humid environment. It is suitable for temperature detection in freezing and refrigeration environments such as refrigerators, indoor and electromechanical equipment temperature detection, soil temperature detection, hot water tank temperature control and other scenarios. It can be used with Arduino, micro:bit and other main controllers. It not only supports mind+ and makecode graphical programming, but also supports programming-free functions.

The waterproof temperature sensor can be used with Arduino, Micro:bit and other main controllers. Kasutamisel, a pull-up resistor must be connected and used with a pluggable sensor adapter.
Connect the circuit as shown in the figure below. After powering on, put the probe of the waterproof temperature sensor into the object to be measured, and the temperature value of the measured object can be directly read through the display module. The temperature sensing range of the waterproof temperature sensor is between -55℃~+125℃, and the temperature display range is -10°C+85°C (error ±0.5°C).

Märkus: Although the product can work normally at 125°C. Siiski, since the cable is made of polyvinyl chloride (PVC) material and is not as heat-resistant as the sensor, we recommend not placing it in a place where the temperature is higher than 100°C.

Principle Introduction
The probe of the TPE Plastic Overmolding sensor uses a thermistor and is potted with a sealant with high thermal conductivity. The high sensitivity and minimal temperature delay of the sensor are guaranteed, and each pin of the chip itself is separated by a heat shrink tube to prevent short circuits. It is packaged with high-quality stainless steel tubes to achieve waterproof, moisture-proof and rust-proof functions.

Külmumistemperatuuri andur Sulatusanduri sond

Kirjeldus

TÜÜP:	TPE Plastic Overmolding sensor	B25/50:	3950K, 3977K, 3435K
Anduri pea:	O Ring, Kahvel metall, Süstitud toru, NPT, M16, roostevaba terastoru	Traat:	CL2 PT4,#24 2466,#28 1332
Kasutamine:	Külmiku sulatusandur, Kiirveesoojendid, veesoojendi, konditsioneer, külmkapp, vee purskkaev, induktsioonpliit, kohvimasin	Pn (nimivõimsus):	50mw
Kõrge valgus:	EPCOS / AVX / SEMITEC /SUBARA / MITSUBISHI / OHIZUMI NTC termistorandur, TPE Plastic Overmolding sensor

Custom TPE Plastic Overmolding ntc temperature sensor Wire 0.5M~10M Theory Signal Output Origin.

Spetsifikatsiooni nimi	Ulatus	Avastamise seisukord
R25(nimitakistuse väärtus)	1k, 2k, 2.7k, 3k, 5k, 10k, 15k, 20k, 30k, 40k, 47k, 50k, 100k, 200k (EPCOS / AVX / SEMITEC /SUBARA / MITSUBISHI / OHIZUMI NTC termistor)	Konstantne temperatuur 25℃±0,05℃
R25 Lubatud hälve(%)	±1,±2, ±3, ±5, ±10	Konstantne temperatuur 25℃±0,05℃
B25/50 või B25/85(materjali koefitsient)(soojustundlikkuse indeks)	2500~5000K	Konstantne temperatuur 25℃±0,05℃ Konstantne temperatuur 85℃±0,05℃
B25/50 Väärtuse lubatud hälve(%)	±1,±2	Konstantne temperatuur 25℃±0,05℃ Konstantne temperatuur 50℃±0,05℃
∫(hajumise koefitsient)	≥0,8 mw/℃	Staatiline õhus
T(termiline ajakonstant)	≤25S	Staatiline õhus
Vastamisi(Töötemperatuur)	-30℃ ~ +120 ℃
Pn (nimivõimsus)	50mw	töötemperatuuri piires
Korpus ja pea		Kahvlipea, O rõnga pea,tilgad veepead, Metallist korpus, Keermega vaskkohver, süstimispea, roostevaba terastoru, või vastavalt kliendi joonisele
Plii traat		#24 30# 2651, UL4411 28#, topeltjuhtmega juht ja nii edasi, või vastavalt kliendi soovile.
Terminal		Neid saab neetida vastavalt erinevate klemmide nõuetele

Teenused
1. Teie päringule vastatakse aja jooksul 24 tundi;
2. Hästi koolitatud ja kogenud töötajad on alati teie teenistuses.
3. Unikaalsed disaintooted ja paljud privaatsed vormitooted ootavad teie valikut.
4. Kaitske rangelt oma isiklikku teavet ja oma disainiideid.
KKK

Q1. Kas mul on NTC tellimuse näidis?, PT100, PT1000, TTA-d, ja Ds18b20 SENSOR?
A: Jah, tervitame proovitellimust kvaliteedi testimiseks ja kontrollimiseks. Segaproovid on vastuvõetavad.