NTC temperature sensor with Overmolding Terminal Connection Line

NTC temperature sensor probe with Overmolding Connector (JST, Molex, RJ11, RJ12, RJ45, RJ50, XH, SM, PH, Aviation plug, terminal blocks, 5557, Faston terminal, audio jack, முதலியன). The sensor head is made from TPE material, which has a good adhesion and sealing. The sensor of Waterproof TPE plastic overmolding NTC thermistor is a kind of waterproof sensor solution. The sensor head is made from TPE material, which has a good adhesion and sealing. Softness and flexibility make this product widely used in a variety of applications.

The flexible and wide temperature range cable makes this type of probe particularly advantageous for cold detection applications.

The specifications of the sensor and the length of the cable can be customized according to requirements.

Waterproof NTC sensor TPE Overmolding water temperature measurement

TPE Overmolding10K 3950 water tank temperature sensor cable With 6.35mm audio plug

Stainless steel NTC sensor with TPE Overmolding connector

Waterproof NTC, PT100, DS18B20 temperature sensors can be used in many places, such as soil temperature detection, hot water tank temperature control, முதலியன. The waterproof temperature sensor is a TPE Plastic Overmolding temperature sensor. This sensor can play a great role in measuring the temperature at a distance and in a humid environment. It is suitable for temperature detection in freezing and refrigeration environments such as refrigerators, indoor and electromechanical equipment temperature detection, soil temperature detection, hot water tank temperature control and other scenarios. It can be used with Arduino, micro:bit and other main controllers. It not only supports mind+ and makecode graphical programming, but also supports programming-free functions.

The waterproof temperature sensor can be used with Arduino, Micro:bit and other main controllers. பயன்படுத்தும் போது, a pull-up resistor must be connected and used with a pluggable sensor adapter.
Connect the circuit as shown in the figure below. After powering on, put the probe of the waterproof temperature sensor into the object to be measured, and the temperature value of the measured object can be directly read through the display module. The temperature sensing range of the waterproof temperature sensor is between -55℃~+125℃, and the temperature display range is -10°C+85°C (error ±0.5°C).

குறிப்பு: Although the product can work normally at 125°C. எனினும், since the cable is made of polyvinyl chloride (PVC) material and is not as heat-resistant as the sensor, we recommend not placing it in a place where the temperature is higher than 100°C.

Principle Introduction
The probe of the TPE Plastic Overmolding sensor uses a thermistor and is potted with a sealant with high thermal conductivity. The high sensitivity and minimal temperature delay of the sensor are guaranteed, and each pin of the chip itself is separated by a heat shrink tube to prevent short circuits. It is packaged with high-quality stainless steel tubes to achieve waterproof, moisture-proof and rust-proof functions.

விளக்கம்

Custom TPE Plastic Overmolding ntc temperature sensor Wire 0.5M~10M Theory Signal Output Origin.

சேவைகள்
1. உங்கள் விசாரணைக்கு பதில் அளிக்கப்படும் 24 மணி;
2. நன்கு பயிற்சி பெற்ற மற்றும் அனுபவம் வாய்ந்த ஊழியர்கள் எப்போதும் உங்கள் சேவையில் இருப்பார்கள்.
3. தனித்துவமான வடிவமைப்பு தயாரிப்புகள் மற்றும் பல தனியார் அச்சு தயாரிப்புகள் உங்கள் விருப்பத்திற்காக காத்திருக்கின்றன.
4. உங்கள் தனிப்பட்ட தகவல் மற்றும் உங்கள் வடிவமைப்பு யோசனைகளை கண்டிப்பாக பாதுகாக்கவும்.
கேள்விகள்

Q1. என்டிசிக்கான மாதிரி ஆர்டர் கிடைக்குமா?, PT100,PT1000, RTDகள், மற்றும் Ds18b20 சென்சார்?
A: ஆம், சோதனை மற்றும் தரத்தை சரிபார்க்க மாதிரி ஆர்டரை நாங்கள் வரவேற்கிறோம். கலப்பு மாதிரிகள் ஏற்றுக்கொள்ளத்தக்கவை.