NTC temperatursensor med Overmolding Terminal Connection Line

NTC temperaturfølersonde med Overmolding Connector (JST, Molex, RJ11, RJ12, RJ45, RJ50, XH, SM, PH, Luftfartsplugg, rekkeklemmer, 5557, Faston terminal, lydkontakt, osv). Sensorhodet er laget av TPE-materiale, som har god vedheft og tetting. The sensor of Waterproof TPE plastic overmolding NTC thermistor is a kind of waterproof sensor solution. Sensorhodet er laget av TPE-materiale, som har god vedheft og tetting. Softness and flexibility make this product widely used in a variety of applications.

The flexible and wide temperature range cable makes this type of probe particularly advantageous for cold detection applications.

The specifications of the sensor and the length of the cable can be customized according to requirements.

Waterproof NTC sensor TPE Overmolding water temperature measurement

TPE Overmolding10K 3950 vanntank temperatursensor kabel Med 6,35 mm lydplugg

NTC-sensor i rustfritt stål med TPE Overmolding-kontakt

Subject	Spesifikasjon	More options
Sensor	NTC 10KΩ	NTC 10K, NTC 50KΩ, NTC 100KΩ, PT100, PT1000, DS18B20, osv.
Kabel	TPE cable	PVC cable, PU cable, silikonkabel, osv.
Kobling	Nothing	JST, Molex, RJ11, RJ12, RJ45, RJ50, XH, SM, PH, Luftfartsplugg, rekkeklemmer, 5557, Faston terminal, lydkontakt, osv.
Precision	1%	1,5%, 2%, 2,5%, 3%, osv.
IP class	IP68	IP65, IP66, IP68, osv.

Waterproof NTC, PT100, DS18B20 temperature sensors can be used in many places, such as soil temperature detection, hot water tank temperature control, osv. The waterproof temperature sensor is a TPE Plastic Overmolding temperature sensor. This sensor can play a great role in measuring the temperature at a distance and in a humid environment. It is suitable for temperature detection in freezing and refrigeration environments such as refrigerators, indoor and electromechanical equipment temperature detection, soil temperature detection, hot water tank temperature control and other scenarios. It can be used with Arduino, micro:bit and other main controllers. It not only supports mind+ and makecode graphical programming, but also supports programming-free functions.

The waterproof temperature sensor can be used with Arduino, Micro:bit and other main controllers. Ved bruk, a pull-up resistor must be connected and used with a pluggable sensor adapter.
Connect the circuit as shown in the figure below. After powering on, put the probe of the waterproof temperature sensor into the object to be measured, and the temperature value of the measured object can be directly read through the display module. The temperature sensing range of the waterproof temperature sensor is between -55℃~+125℃, and the temperature display range is -10°C+85°C (error ±0.5°C).

Note: Although the product can work normally at 125°C. Imidlertid, since the cable is made of polyvinyl chloride (PVC) material and is not as heat-resistant as the sensor, we recommend not placing it in a place where the temperature is higher than 100°C.

Principle Introduction
The probe of the TPE Plastic Overmolding sensor uses a thermistor and is potted with a sealant with high thermal conductivity. The high sensitivity and minimal temperature delay of the sensor are guaranteed, and each pin of the chip itself is separated by a heat shrink tube to prevent short circuits. It is packaged with high-quality stainless steel tubes to achieve waterproof, moisture-proof and rust-proof functions.

Frysetemperatursensor Avrimingssensorprobe

Beskrivelse

TYPE:	TPE Plastic Overmolding sensor	B25/50:	3950K, 3977K, 3435K
Sensorhode:	O Ring, Gaffel metall, Injisert rør, PT, M16, rustfritt stålrør	Metalltråd:	CL2 PT4, #24 2466,#28 1332
Bruk:	Kjøleskapsavrimingssensor, Øyeblikkelig vannvarmere, varmtvannsbereder, klimaanlegg, kjøleskap, vannfontene, induksjonskomfyr, kaffetrakter	Pn (vurdert Power):	50mw
Høyt lys:	EPCOS / AVX / SEMITEC /SUBARA / MITSUBISHI / OHIZUMI NTC termistorsensor, TPE Plastic Overmolding sensor

Custom TPE Plastic Overmolding ntc temperature sensor Wire 0.5M~10M Theory Signal Output Origin.

Spesifikasjonsnavn	Omfang	Deteksjonstilstand
R25(nominell motstandsverdi)	1k, 2k, 2.7k, 3k, 5k, 10k, 15k, 20k, 30k, 40k, 47k, 50k, 100k, 200k (EPCOS / AVX / SEMITEC /SUBARA / MITSUBISHI / OHIZUMI NTC termistor)	Konstant temperatur 25℃±0,05℃
R25 Tillatt avvik(%)	±1,±2, ±3, ±5, ±10	Konstant temperatur 25℃±0,05℃
B25/50 eller B25/85(materialkoeffisient)(termisk følsomhetsindeks)	2500~5000K	Konstant temperatur 25℃±0,05℃ Konstant temperatur 85℃±0,05℃
B25/50 Verdi tillatt avvik(%)	±1,±2	Konstant temperatur 25℃±0,05℃ Konstant temperatur 50℃±0,05℃
∫(dissipasjonskoeffisient)	≥0,8mw/℃	Statisk i luften
T(termisk tidskonstant)	≤25S	Statisk i luften
Vendt(Arbeidstemperatur)	-30℃~+120℃
Pn (merkeeffekt)	50mw	innenfor arbeidstemperatur
Etui og hode		Gaffelhode, O ringhode,dråper vannhode, Metallkoffert, Gjenge kobberkasse, injeksjonshode, rustfritt stålrør, eller i henhold til kundens tegning
Blytråd		#24 30# 2651, UL4411 28#, dobbel kablet leder og så videre, eller i henhold til kundens forespørsel.
Terminal		Kan klinkes i henhold til kravene til ulike terminaler

Tjenester
1. Din henvendelse vil bli besvart innen 24 timer;
2. Godt trent og erfarent personale står alltid til tjeneste.
3. Unike designprodukter og mange private muggprodukter venter på ditt valg.
4. Beskytt din private informasjon og dine designideer strengt.
FAQ

Q1. Kan jeg få en prøvebestilling for NTC, PT100, PT1000, RTS, og Ds18b20 SENSOR?
EN: Ja, Vi ønsker velkommen prøvebestilling for å teste og sjekke kvalitet. Blandede prøver er akseptable.