NTC senzor temperature s priključnim vodom za preklapanje

Sonda senzora temperature NTC s konektorom za prelivanje (JST, Molex, RJ11, RJ12, RJ45, RJ50, XH, SM, PH, Zrakoplovni utikač, stezaljke, 5557, Faston terminal, audio priključak, itd). Glava senzora izrađena je od TPE materijala, koji ima dobro prianjanje i brtvljenje. The sensor of Waterproof TPE plastic overmolding NTC thermistor is a kind of waterproof sensor solution. Glava senzora izrađena je od TPE materijala, koji ima dobro prianjanje i brtvljenje. Softness and flexibility make this product widely used in a variety of applications.

The flexible and wide temperature range cable makes this type of probe particularly advantageous for cold detection applications.

The specifications of the sensor and the length of the cable can be customized according to requirements.

Waterproof NTC sensor TPE Overmolding water temperature measurement

TPE prelijevanje 10K 3950 kabel senzora temperature spremnika za vodu s audio utikačem od 6,35 mm

NTC senzor od nehrđajućeg čelika s TPE preljevnim konektorom

Subject	Specifikacija	More options
Senzor	NTC 10KΩ	NTC 10K, NTC 50KΩ, NTC 100KΩ, PT100, PT1000, DS18B20, itd.
Kabel	TPE cable	PVC cable, PU cable, silikonski kabel, itd.
Connector	Nothing	JST, Molex, RJ11, RJ12, RJ45, RJ50, XH, SM, PH, Zrakoplovni utikač, stezaljke, 5557, Faston terminal, audio priključak, itd.
Precision	1%	1,5%, 2%, 2,5%, 3%, itd.
IP class	IP68	IP65, IP66, IP68, itd.

Waterproof NTC, PT100, DS18B20 temperature sensors can be used in many places, such as soil temperature detection, hot water tank temperature control, itd. The waterproof temperature sensor is a TPE Plastic Overmolding temperature sensor. This sensor can play a great role in measuring the temperature at a distance and in a humid environment. It is suitable for temperature detection in freezing and refrigeration environments such as refrigerators, indoor and electromechanical equipment temperature detection, soil temperature detection, hot water tank temperature control and other scenarios. It can be used with Arduino, micro:bit and other main controllers. It not only supports mind+ and makecode graphical programming, but also supports programming-free functions.

The waterproof temperature sensor can be used with Arduino, Micro:bit and other main controllers. Prilikom korištenja, a pull-up resistor must be connected and used with a pluggable sensor adapter.
Connect the circuit as shown in the figure below. After powering on, put the probe of the waterproof temperature sensor into the object to be measured, and the temperature value of the measured object can be directly read through the display module. The temperature sensing range of the waterproof temperature sensor is between -55℃~+125℃, and the temperature display range is -10°C+85°C (error ±0.5°C).

Bilješka: Although the product can work normally at 125°C. Međutim, since the cable is made of polyvinyl chloride (PVC) material and is not as heat-resistant as the sensor, we recommend not placing it in a place where the temperature is higher than 100°C.

Principle Introduction
The probe of the TPE Plastic Overmolding sensor uses a thermistor and is potted with a sealant with high thermal conductivity. The high sensitivity and minimal temperature delay of the sensor are guaranteed, and each pin of the chip itself is separated by a heat shrink tube to prevent short circuits. It is packaged with high-quality stainless steel tubes to achieve waterproof, moisture-proof and rust-proof functions.

Senzor temperature smrzavanja Sonda senzora odmrzavanja

Opis

TIP:	TPE Plastic Overmolding sensor	B25/50:	3950K, 3977K, 3435K
Glava senzora:	O prsten, Metalna vilica, Injektirana cijev, NPT, M16, cijev od nehrđajućeg čelika	Žica:	CL2 PT4, #24 2466,#28 1332
Korištenje:	Senzor odleđivanja hladnjaka, Instant grijači vode, bojler, klima uređaj, hladnjak, vodoskok, indukcijsko kuhalo, aparat za kavu	Pn (nazivna snaga):	50mw
Visoko svjetlo:	EPCOS / AVX / SEMITEC /SUBARA / MITSUBISHI / OHIZUMI NTC termistorski senzor, TPE Plastic Overmolding sensor

Custom TPE Plastic Overmolding ntc temperature sensor Wire 0.5M~10M Theory Signal Output Origin.

Naziv specifikacije	Opseg	Uvjet otkrivanja
R25(nazivna vrijednost otpora)	1k, 2k, 2.7k, 3k, 5k, 10k, 15k, 20k, 30k, 40k, 47k, 50k, 100k, 200k (EPCOS / AVX / SEMITEC /SUBARA / MITSUBISHI / OHIZUMI NTC termistor)	Konstantna temperatura 25℃±0,05℃
R25 Dopušteno odstupanje(%)	±1,±2, ±3, ±5, ±10	Konstantna temperatura 25℃±0,05℃
B25/50 ili B25/85(materijalni koeficijent)(indeks toplinske osjetljivosti)	2500~5000K	Konstantna temperatura 25℃±0,05℃ Konstantna temperatura 85℃±0,05℃
B25/50 Vrijednost dopuštene varijance(%)	±1,±2	Konstantna temperatura 25℃±0,05℃ Konstantna temperatura 50℃±0,05℃
∫(koeficijent disipacije)	≥0,8 mw/℃	Statika u zraku
T(termalna vremenska konstanta)	≤25S	Statika u zraku
Suočavanje(Radna temperatura)	-30℃~+120℃
Pn (nazivna snaga)	50mw	unutar radne temperature
Slučaj i glava		Glava vilice, O prstenasta glava,kapi vode glava, Metalno kućište, Bakreno kućište s navojem, glava za ubrizgavanje, cijev od nehrđajućeg čelika, ili prema nacrtu klijenta
Vodeća žica		#24 30# 2651, UL4411 28#, dvostruki žičani vodič i tako dalje, ili prema zahtjevu klijenta.
Terminal		Može se zakivati prema zahtjevima različitih terminala

Usluge
1. Na vaš će upit biti odgovoreno u roku 24 sati;
2. Dobro obučeno i iskusno osoblje uvijek vam je na usluzi.
3. Jedinstveni dizajnerski proizvodi i mnogi privatni kalupni proizvodi čekaju na vaš izbor.
4. Strogo čuvajte svoje privatne podatke i svoje ideje dizajna.
FAQ

P1. Mogu li dobiti uzorak narudžbe za NTC, PT100, PT1000, RTS, i Ds18b20 SENZOR?
A: Da, pozdravljamo narudžbu uzorka za testiranje i provjeru kvalitete. Mješoviti uzorci su prihvatljivi.