Kineski prilagođeni sklop sonde senzora termistora za kontrolu temperature

An NTC thermistor is a temperature sensor that uses the resistance properties of ceramic/metal composites to measure the temperature. Our full spectrum NTC thermistor is a resistance thermometer, or a resistor whose resistance is dependent on temperature. The term is a combination of “thermal” and “resistor”. It is made of metallic oxides, pressed into a bead, disk, or cylindrical shape and then encapsulated with an impermeable material such as epoxy or glass. Vrhunski proizvođač sondi senzora otpornika — YAXUN je specijaliziran za termistore koji imaju temperaturnu osjetljivost i kvalificirani su za AEC-Q200. TCTR – NTC termistor s debelim filmom. 47-1.6MΩ. Najstroža tolerancija 1%. B vrijednost 2410K – 4800K.
Senzor temperature termistora — Linearni termistori na bazi silicija po istoj cijeni i veličini kao i tradicionalni NTC termistori. Postignite pouzdanost sustava visoke točnosti s najmanjim linearnim termistorima u industriji.
Field-proven thermistor level-sensing technology with NPT mounting threads;
SP-M models temperature sensor are designed for use with ST-15 Control Monitors Electrical appliances, automobili, aviation, small household appliances, toys;
Typical uses include storage tanks, double-containment piping trenches, and double-wall storage tank interstitial space monitoring;
Years of dependable, virtually maintenance-free operation;
Sensors can be easily extended to desired length at installation site using a 3/8” x 3/8” coupler and the required length of 3/8” NPT pipe.

Ender 3 Thermistor Sensor, Upgrade HT-NTC100K 3D Printer Thermistor Sensor: Thermistor temperature sensor. Metal head diameter: 3 mm, head length: 15 mm,cable wire length: 1 meter,konektor: XH2.54 2PIN, （Suitable for heating blocks with holes of 3 mm*15 mm-3 mm*20 mm）;
Widly Compatibility: Product recommended operating temperature -50 °C ~ +280 ° C, can replace the cartridge K-type thermocouple temperature sensor. Compatible with the heatblocks with 3 mm hole,takav: V6 Volcano PT100 type heated block, itd;
Sensors is accurate: The best feature was the flexible and heat shielded probe leads to the copper sensor. Unlike the other with a nickel plated probe/heat shrink, this can be fitted in very tight spots without worry. Be sure you redo your PID calibration;
Long Service Life: Compared with the same type that are insulated with ordinary heat shrinkable tubes, ours uses glass fiber with a temp resistance of 400C degrees for insulation to avoid the possibility of thermal short circuit during high temp work;
Fit ALL-METAL HOTEND: Work for E3D-V6 Volcano PT100 Ender 3 series all-metal hotend such as spider-hotend,K1-red-Lizard-hotend,dragonfly-hot-end,voron-hotend etc.

3D Termistor pisača 100k NTC 3950 s 1 Mjerač proširene kabelske žice Koristite za Ender 3 V2 Pro CR10 i drugi Hotend ekstrudera za 3D pisače

Heater NTC thermistor: with M3 Thread Stud thermistor，Fast-Plug Connector Compatible with 3/3 V2/3 Neo/3 V2 Neo/3S/3 PRO/5/5

NTC100K termistorski senzor za kreativnost 3 v2 Nadogradnja 3x15mm 3950 Kompatibilan s termistorom

Radial Leaded Resin Coated NTC Thermistor Features
Visoka točnost mjerenja.
Tight tolerance on resistance and Beta value.
Fast response, small dimension.
Can operate in long time stability.
Nominal resistance @25C can be from R25 1kΩ–1000kΩ.
Typical resistance at 25C R25 1k ohm, 2k ohm, 2252 ohm, 3k ohm, 4.7k ohm, 5k ohm, 6.8k ohm, 10k ohm, 15k ohm, 20k ohm, 30k ohm, 40k ohm, 47k ohm, 50k ohm, 100k ohm, 150k ohm, 1000k ohm, itd.
Dissipation factor: ≥3.0 mW/C in still air.
Thermal time constant: ≤12 seconds in still air.
Raspon radne temperature: -45C — +125C.

Bilješke：□ in the part number for filling in resistance tolerance,
optional for ±1%(F), ±2%(G), ±3%(H), or ±5%(J).