سنسور دمای NTC با خط اتصال ترمینال Overmolding

پروب سنسور دما NTC با کانکتور Overmolding (JST, Molex, RJ11, RJ12, RJ45, RJ50, XH, اس ام, PH, پلاگین هوانوردی, بلوک های ترمینال, 5557, ترمینال فاستون, جک صدا, OTC). سر سنسور از مواد TPE ساخته شده است, که چسبندگی و آب بندی خوبی دارد. The sensor of Waterproof TPE plastic overmolding NTC thermistor is a kind of waterproof sensor solution. سر سنسور از مواد TPE ساخته شده است, که چسبندگی و آب بندی خوبی دارد. Softness and flexibility make this product widely used in a variety of applications.

The flexible and wide temperature range cable makes this type of probe particularly advantageous for cold detection applications.

The specifications of the sensor and the length of the cable can be customized according to requirements.

Waterproof NTC sensor TPE Overmolding water temperature measurement

TPE Overmolding10K 3950 کابل سنسور دمای مخزن آب با فیش صوتی 6.35 میلی متری

سنسور NTC فولاد ضد زنگ با کانکتور TPE Overmolding

Waterproof NTC, PT100, DS18B20 temperature sensors can be used in many places, such as soil temperature detection, hot water tank temperature control, OTC. The waterproof temperature sensor is a TPE Plastic Overmolding temperature sensor. This sensor can play a great role in measuring the temperature at a distance and in a humid environment. It is suitable for temperature detection in freezing and refrigeration environments such as refrigerators, indoor and electromechanical equipment temperature detection, soil temperature detection, hot water tank temperature control and other scenarios. It can be used with Arduino, micro:bit and other main controllers. It not only supports mind+ and makecode graphical programming, but also supports programming-free functions.

The waterproof temperature sensor can be used with Arduino, Micro:bit and other main controllers. هنگام استفاده, a pull-up resistor must be connected and used with a pluggable sensor adapter.
Connect the circuit as shown in the figure below. After powering on, put the probe of the waterproof temperature sensor into the object to be measured, and the temperature value of the measured object can be directly read through the display module. The temperature sensing range of the waterproof temperature sensor is between -55℃~+125℃, and the temperature display range is -10°C+85°C (error ±0.5°C).

توجه داشته باشید: Although the product can work normally at 125°C. هر چند, since the cable is made of polyvinyl chloride (PVC) material and is not as heat-resistant as the sensor, we recommend not placing it in a place where the temperature is higher than 100°C.

Principle Introduction
The probe of the TPE Plastic Overmolding sensor uses a thermistor and is potted with a sealant with high thermal conductivity. The high sensitivity and minimal temperature delay of the sensor are guaranteed, and each pin of the chip itself is separated by a heat shrink tube to prevent short circuits. It is packaged with high-quality stainless steel tubes to achieve waterproof, moisture-proof and rust-proof functions.

شرح

Custom TPE Plastic Overmolding ntc temperature sensor Wire 0.5M~10M Theory Signal Output Origin.

خدمات
1. درخواست شما در داخل پاسخ داده خواهد شد 24 ساعت;
2. کادری مجرب و آموزش دیده همیشه در خدمت شما هستند.
3. محصولات طراحی منحصر به فرد و بسیاری از محصولات قالب خصوصی منتظر انتخاب شما هستند.
4. از اطلاعات خصوصی و ایده های طراحی خود به شدت محافظت کنید.
پرسش

Q1. آیا می توانم یک سفارش نمونه برای NTC داشته باشم؟, PT100، PT1000, RTS, و سنسور Ds18b20?
بوها: بله, ما از سفارش نمونه برای تست و بررسی کیفیت استقبال می کنیم. نمونه های مخلوط قابل قبول است.