مونتاژ پروب سنسور ترمیستور سفارشی چین برای کنترل دما

An NTC thermistor is a temperature sensor that uses the resistance properties of ceramic/metal composites to measure the temperature. Our full spectrum NTC thermistor is a resistance thermometer, or a resistor whose resistance is dependent on temperature. The term is a combination of “thermal” and “resistor”. It is made of metallic oxides, pressed into a bead, دیسک, or cylindrical shape and then encapsulated with an impermeable material such as epoxy or glass. تولید کننده پروب سنسور مقاومت بالا - YAXUN متخصص در ترمیستور دارای حساسیت دما و واجد شرایط AEC-Q200 است.. TCTR – ترمیستور فیلم ضخیم NTC. 47-1.6MΩ. سخت ترین تحمل 1%. B ارزش 2410K – 4800k.
سنسور دما ترمیستور - ترمیستورهای خطی مبتنی بر سیلیکون با قیمت و اندازه ترمیستورهای سنتی NTC. دستیابی به قابلیت اطمینان سیستم با دقت بالا با کوچکترین ترمیستورهای خطی صنعت.
Field-proven thermistor level-sensing technology with NPT mounting threads;
SP-M models temperature sensor are designed for use with ST-15 Control Monitors Electrical appliances, اتومبیل ها, aviation, small household appliances, toys;
Typical uses include storage tanks, double-containment piping trenches, and double-wall storage tank interstitial space monitoring;
Years of dependable, virtually maintenance-free operation;
Sensors can be easily extended to desired length at installation site using a 3/8” x 3/8” coupler and the required length of 3/8” NPT pipe.

Ender 3 Thermistor Sensor, Upgrade HT-NTC100K 3D Printer Thermistor Sensor: سنسور دما ترمیستور. Metal head diameter: 3 میلی متر, head length: 15 میلی متر,cable wire length: 1 meter,اتصال دهنده: XH2.54 2PIN, （Suitable for heating blocks with holes of 3 mm*15 mm-3 mm*20 mm）;
Widly Compatibility: Product recommended operating temperature -50 °C ~ +280 درجه سانتیگراد, can replace the cartridge K-type thermocouple temperature sensor. Compatible with the heatblocks with 3 mm hole,مانند: V6 Volcano PT100 type heated block, OTC;
Sensors is accurate: The best feature was the flexible and heat shielded probe leads to the copper sensor. Unlike the other with a nickel plated probe/heat shrink, this can be fitted in very tight spots without worry. Be sure you redo your PID calibration;
Long Service Life: Compared with the same type that are insulated with ordinary heat shrinkable tubes, ours uses glass fiber with a temp resistance of 400C degrees for insulation to avoid the possibility of thermal short circuit during high temp work;
Fit ALL-METAL HOTEND: Work for E3D-V6 Volcano PT100 Ender 3 series all-metal hotend such as spider-hotend,K1-red-Lizard-hotend,dragonfly-hot-end,voron-hotend etc.

3پرینتر D ترمیستور 100k NTC 3950 با 1 استفاده از سیم کابل متری برای Ender 3 V2 Pro CR10 و سایر پرینترهای سه بعدی اکسترودر Hotend

Heater NTC thermistor: with M3 Thread Stud thermistor，Fast-Plug Connector Compatible with 3/3 V2/3 Neo/3 V2 Neo/3S/3 PRO/5/5

سنسور ترمیستور NTC100K برای خلاقیت 3 v2 ارتقاء 3x15mm 3950 سازگار با ترمیستور

Radial Leaded Resin Coated NTC Thermistor Features
High measurement accuracy.
Tight tolerance on resistance and Beta value.
Fast response, small dimension.
Can operate in long time stability.
Nominal resistance @25C can be from R25 1kΩ–1000kΩ.
Typical resistance at 25C R25 1k ohm, 2k اهم, 2252 ohm, 3k اهم, 4.7k اهم, 5k اهم, 6.8k اهم, 10k اهم, 15k اهم, 20k اهم, 30k اهم, 40k اهم, 47k اهم, 50k اهم, 100k اهم, 150k اهم, 1000k اهم, OTC.
Dissipation factor: ≥3.0 mW/C in still air.
ثابت زمانی حرارتی: ≤12 seconds in still air.
محدوده دمای عملیاتی: -45C — +125C.

یادداشت ها：□ in the part number for filling in resistance tolerance,
optional for ±1%(اف), ±2%(G), ±3%(اچ), or ±5%(جی).