NTC temperaturni senzor sa priključnom linijom za prelijevanje terminala

NTC sonda temperaturnog senzora sa konektorom za prelijevanje (JST, Molex, RJ11, RJ12, RJ45, RJ50, XH, SM, PH, Aviation plug, terminalni blokovi, 5557, Faston terminal, audio priključak, itd). Glava senzora je napravljena od TPE materijala, koji ima dobro prianjanje i zaptivanje. The sensor of Waterproof TPE plastic overmolding NTC thermistor is a kind of waterproof sensor solution. Glava senzora je napravljena od TPE materijala, koji ima dobro prianjanje i zaptivanje. Softness and flexibility make this product widely used in a variety of applications.

The flexible and wide temperature range cable makes this type of probe particularly advantageous for cold detection applications.

The specifications of the sensor and the length of the cable can be customized according to requirements.

Waterproof NTC sensor TPE Overmolding water temperature measurement

TPE Overmolding10K 3950 Kabel senzora temperature rezervoara za vodu Sa audio priključkom od 6,35 mm

NTC senzor od nerđajućeg čelika sa TPE konektorom za prelivanje

Subject	Specifikacija	More options
Senzor	NTC 10KΩ	NTC 10K, NTC 50KΩ, NTC 100KΩ, PT100, PT1000, DS18B20, itd.
Kabl	TPE cable	PVC cable, PU cable, silikonski kabl, itd.
Connector	Nothing	JST, Molex, RJ11, RJ12, RJ45, RJ50, XH, SM, PH, Aviation plug, terminalni blokovi, 5557, Faston terminal, audio priključak, itd.
Precision	1%	1,5%, 2%, 2,5%, 3%, itd.
IP class	IP68	IP65, IP66, IP68, itd.

Waterproof NTC, PT100, DS18B20 temperature sensors can be used in many places, such as soil temperature detection, hot water tank temperature control, itd. The waterproof temperature sensor is a TPE Plastic Overmolding temperature sensor. This sensor can play a great role in measuring the temperature at a distance and in a humid environment. It is suitable for temperature detection in freezing and refrigeration environments such as refrigerators, indoor and electromechanical equipment temperature detection, soil temperature detection, hot water tank temperature control and other scenarios. It can be used with Arduino, micro:bit and other main controllers. It not only supports mind+ and makecode graphical programming, but also supports programming-free functions.

The waterproof temperature sensor can be used with Arduino, Micro:bit and other main controllers. Prilikom upotrebe, a pull-up resistor must be connected and used with a pluggable sensor adapter.
Connect the circuit as shown in the figure below. After powering on, put the probe of the waterproof temperature sensor into the object to be measured, and the temperature value of the measured object can be directly read through the display module. The temperature sensing range of the waterproof temperature sensor is between -55℃~+125℃, and the temperature display range is -10°C+85°C (error ±0.5°C).

Napomena: Although the product can work normally at 125°C. Međutim, since the cable is made of polyvinyl chloride (PVC) material and is not as heat-resistant as the sensor, we recommend not placing it in a place where the temperature is higher than 100°C.

Principle Introduction
The probe of the TPE Plastic Overmolding sensor uses a thermistor and is potted with a sealant with high thermal conductivity. The high sensitivity and minimal temperature delay of the sensor are guaranteed, and each pin of the chip itself is separated by a heat shrink tube to prevent short circuits. It is packaged with high-quality stainless steel tubes to achieve waterproof, moisture-proof and rust-proof functions.

Senzor temperature smrzavanja Sonda senzora odmrzavanja

Opis

TYPE:	TPE Plastic Overmolding sensor	B25/50:	3950K, 3977K, 3435K
Glava senzora:	O Ring, Fork Metal, Injected Tube, NPT, M16, Cijev od nehrđajućeg čelika	Žica:	CL2 PT4,#24 2466,#28 1332
Upotreba:	Senzor odmrzavanja frižidera, Instant bojleri, bojler, klima uređaj, frižider, fontana, indukcijski štednjak, aparat za kafu	Pn (ocijenjena snaga):	50mw
High Light:	EPCOS / AVX / SEMITEC /SUBARA / MITSUBISHI / OHIZUMI NTC termistor senzor, TPE Plastic Overmolding sensor

Custom TPE Plastic Overmolding ntc temperature sensor Wire 0.5M~10M Theory Signal Output Origin.

Naziv specifikacije	Obim	Detection Condition
R25(nominalna vrijednost otpora)	1k, 2k, 2.7k, 3k, 5k, 10k, 15k, 20k, 30k, 40k, 47k, 50k, 100k, 200k (EPCOS / AVX / SEMITEC /SUBARA / MITSUBISHI / OHIZUMI NTC termistor)	Konstantna temperatura 25℃±0.05℃
R25 Dozvoljeno odstupanje(%)	±1,±2, ±3, ±5, ±10	Konstantna temperatura 25℃±0.05℃
B25/50 ili B25/85(materijalni koeficijent)(indeks toplinske osjetljivosti)	2500~5000K	Konstantna temperatura 25℃±0.05℃ Konstantna temperatura 85℃±0.05℃
B25/50 Dozvoljena varijacija vrijednosti(%)	±1,±2	Konstantna temperatura 25℃±0.05℃ Konstantna temperatura 50℃±0.05℃
∫(koeficijent disipacije)	≥0.8mw/℃	Statičnost u vazduhu
T(termička vremenska konstanta)	≤25S	Statičnost u vazduhu
Facing(Radna temperatura)	-30℃~+120℃
Pn (nazivna snaga)	50mw	unutar radne temperature
Slučaj i glava		Glava viljuške, O prstenasta glava,kapi vode, Metalno kućište, Kućište od bakra sa navojem, glava za ubrizgavanje, Cijev od nehrđajućeg čelika, ili prema crtežu klijenta
Olovna žica		#24 30# 2651, UL4411 28#, dvostruko žičani provodnik i tako dalje, ili prema zahtjevu klijenta.
Terminal		Može se zakivati prema zahtjevima raznih terminala

Usluge
1. Na Vaš upit će biti odgovoreno unutar 24 sati;
2. Dobro obučeno i iskusno osoblje vam je uvijek na usluzi.
3. Jedinstveni dizajnerski proizvodi i mnogi privatni proizvodi od kalupa čekaju na vaš izbor.
4. Strogo zaštitite svoje privatne podatke i svoje ideje dizajna.
FAQ

Q1. Mogu li dobiti uzorak narudžbe za NTC, PT100,PT1000, RTDs, i Ds18b20 SENZOR?
A: Da, pozdravljamo narudžbu uzoraka za testiranje i provjeru kvalitete. Mješoviti uzorci su prihvatljivi.