Sensor suhu NTC dengan garis sambungan terminal overmolding

Probe sensor suhu NTC dengan penyambung overmolding (JST, Molex, RJ11, RJ12, RJ45, RJ50, XH, Sm, Ph, Palam penerbangan, Blok terminal, 5557, Terminal Faston, Jack Audio, dll). Kepala sensor dibuat dari bahan TPE, yang mempunyai lekatan dan pengedap yang baik. The sensor of Waterproof TPE plastic overmolding NTC thermistor is a kind of waterproof sensor solution. Kepala sensor dibuat dari bahan TPE, yang mempunyai lekatan dan pengedap yang baik. Softness and flexibility make this product widely used in a variety of applications.

The flexible and wide temperature range cable makes this type of probe particularly advantageous for cold detection applications.

The specifications of the sensor and the length of the cable can be customized according to requirements.

Waterproof NTC sensor TPE Overmolding water temperature measurement

TPE Overmolding10K 3950 kabel sensor suhu tangki air dengan palam audio 6.35mm

Sensor NTC keluli tahan karat dengan penyambung overmolding TPE

Subject	Spesifikasi	More options
Sensor	NTC 10KΩ	NTC 10K, NTC 50KΩ, NTC 100KΩ, PT100, PT1000, DS18B20, dll.
Kabel	TPE cable	PVC cable, PU cable, kabel silikon, dll.
Connector	Nothing	JST, Molex, RJ11, RJ12, RJ45, RJ50, XH, Sm, Ph, Palam penerbangan, Blok terminal, 5557, Terminal Faston, Jack Audio, dll.
Precision	1%	1,5%, 2%, 2,5%, 3%, dll.
IP class	IP68	IP65, IP66, IP68, dll.

Waterproof NTC, PT100, DS18B20 temperature sensors can be used in many places, such as soil temperature detection, hot water tank temperature control, dll. The waterproof temperature sensor is a TPE Plastic Overmolding temperature sensor. This sensor can play a great role in measuring the temperature at a distance and in a humid environment. It is suitable for temperature detection in freezing and refrigeration environments such as refrigerators, indoor and electromechanical equipment temperature detection, soil temperature detection, hot water tank temperature control and other scenarios. It can be used with Arduino, micro:bit and other main controllers. It not only supports mind+ and makecode graphical programming, but also supports programming-free functions.

The waterproof temperature sensor can be used with Arduino, Micro:bit and other main controllers. Semasa menggunakan, a pull-up resistor must be connected and used with a pluggable sensor adapter.
Connect the circuit as shown in the figure below. After powering on, put the probe of the waterproof temperature sensor into the object to be measured, and the temperature value of the measured object can be directly read through the display module. The temperature sensing range of the waterproof temperature sensor is between -55℃~+125℃, and the temperature display range is -10°C+85°C (error ±0.5°C).

Nota: Although the product can work normally at 125°C. Walau bagaimanapun, since the cable is made of polyvinyl chloride (PVC) material and is not as heat-resistant as the sensor, we recommend not placing it in a place where the temperature is higher than 100°C.

Principle Introduction
The probe of the TPE Plastic Overmolding sensor uses a thermistor and is potted with a sealant with high thermal conductivity. The high sensitivity and minimal temperature delay of the sensor are guaranteed, and each pin of the chip itself is separated by a heat shrink tube to prevent short circuits. It is packaged with high-quality stainless steel tubes to achieve waterproof, moisture-proof and rust-proof functions.

Sensor suhu pembekuan defrosting probe sensor

Penerangan

Jenis:	TPE Plastic Overmolding sensor	B25/50:	3950K, 3977K, 3435K
Kepala sensor:	O cincin, Fork Metal, Tiub yang disuntik, Npt, M16, tiub keluli Tainless	Wayar:	CL2 PT4,#24 2466,#28 1332
Penggunaan:	Refrigerator Defrost Sensor, Pemanas air segera, Pemanas air, penghawa dingin, peti sejuk, Air pancut air, periuk induksi, pembuat kopi	Pn (kuasa dinilai):	50mw
Cahaya tinggi:	Epcos / Avx / Semitec /Subara / Mitsubishi / Sensor Thermistor Ohizumi NTC, TPE Plastic Overmolding sensor

Custom TPE Plastic Overmolding ntc temperature sensor Wire 0.5M~10M Theory Signal Output Origin.

Nama spesifikasi	Skop	Keadaan pengesanan
R25(Nilai rintangan nominal)	1k, 2k, 2.7k, 3k, 5k, 10k, 15k, 20k, 30k, 40k, 47k, 50k, 100k, 200k (Epcos / Avx / Semitec /Subara / Mitsubishi / Ohizumi NTC Thermistor)	Suhu malar 25 ℃ ± 0.05 ℃
Varians R25 yang dibenarkan(%)	± 1, ± 2, ± 3, ± 5, ± 10	Suhu malar 25 ℃ ± 0.05 ℃
B25/50 atau B25/85(pekali bahan)(Indeks sensitiviti haba)	2500~ 5000K	Suhu malar 25 ℃ ± 0.05 ℃ Suhu malar 85 ℃ ± 0.05 ℃
Varians nilai b25/50 yang dibenarkan(%)	± 1, ± 2	Suhu malar 25 ℃ ± 0.05 ℃ Suhu malar 50 ℃ ± 0.05 ℃
∫(pekali pelesapan)	≥0.8mw/℃	Statik di udara
T(pemalar masa terma)	≤25s	Statik di udara
Menghadap(Suhu kerja)	-30℃ ~+120 ℃
Pn (kuasa dinilai)	50mw	dalam suhu kerja
Kes dan kepala		Kepala garpu, O kepala cincin,Titisan kepala air, Kes logam, Kes Tembaga Thread, Ketua suntikan, tiub keluli Tainless, atau mengikut lukisan pelanggan
Wayar plumbum		#24 30# 2651, UL4411 28#, konduktor berwayar berganda dan sebagainya, atau mengikut permintaan pelanggan.
Terminal		Boleh dipancarkan mengikut keperluan pelbagai terminal

Perkhidmatan
1. Pertanyaan anda akan dijawab dalam 24 jam;
2. Kakitangan yang terlatih dan berpengalaman sentiasa berada di perkhidmatan anda.
3. Produk reka bentuk yang unik dan banyak produk acuan peribadi sedang menunggu pilihan anda.
4. Lindungi maklumat peribadi anda dengan tegas dan idea reka bentuk anda.
Soalan Lazim

Q1. Bolehkah saya mempunyai pesanan sampel untuk ntc, PT100, PT1000, RTS, dan sensor DS18B20?
A: Ya, Kami mengalu -alukan pesanan sampel untuk menguji dan memeriksa kualiti. Sampel bercampur boleh diterima.