Склоп на сонда со прилагоден термисторски сензор за Кина за контрола на температурата

An NTC thermistor is a temperature sensor that uses the resistance properties of ceramic/metal composites to measure the temperature. Our full spectrum NTC thermistor is a resistance thermometer, or a resistor whose resistance is dependent on temperature. The term is a combination of “thermal” and “resistor”. It is made of metallic oxides, pressed into a bead, disk, or cylindrical shape and then encapsulated with an impermeable material such as epoxy or glass. Производител на сонда со сензор со висока класа на отпор - YAXUN е специјализиран за термистор кој има чувствителност на температура и квалификувани AEC-Q200. TCTR – NTC термистор со дебел филм. 47-1.6MΩ. Најстрога толеранција 1%. B Вредност 2410K – 4800К..
Термисторски сензор за температура — линеарни термистори базирани на силикон со иста цена и големина на традиционалните NTC термистори. Постигнете доверливост на системот со висока прецизност со најмалите линеарни термистори во индустријата.
Field-proven thermistor level-sensing technology with NPT mounting threads;
SP-M models temperature sensor are designed for use with ST-15 Control Monitors Electrical appliances, автомобили, авијација, small household appliances, toys;
Typical uses include storage tanks, double-containment piping trenches, and double-wall storage tank interstitial space monitoring;
Years of dependable, virtually maintenance-free operation;
Sensors can be easily extended to desired length at installation site using a 3/8” x 3/8” coupler and the required length of 3/8” NPT pipe.

Ender 3 Thermistor Sensor, Upgrade HT-NTC100K 3D Printer Thermistor Sensor: Thermistor temperature sensor. Metal head diameter: 3 мм, head length: 15 мм,cable wire length: 1 meter,конектор: XH2.54 2PIN, （Suitable for heating blocks with holes of 3 mm*15 mm-3 mm*20 mm）;
Widly Compatibility: Product recommended operating temperature -50 °C ~ +280 ° C., can replace the cartridge K-type thermocouple temperature sensor. Compatible with the heatblocks with 3 mm hole,како што се: V6 Volcano PT100 type heated block, итн;
Sensors is accurate: The best feature was the flexible and heat shielded probe leads to the copper sensor. Unlike the other with a nickel plated probe/heat shrink, this can be fitted in very tight spots without worry. Be sure you redo your PID calibration;
Long Service Life: Compared with the same type that are insulated with ordinary heat shrinkable tubes, ours uses glass fiber with a temp resistance of 400C degrees for insulation to avoid the possibility of thermal short circuit during high temp work;
Fit ALL-METAL HOTEND: Work for E3D-V6 Volcano PT100 Ender 3 series all-metal hotend such as spider-hotend,K1-red-Lizard-hotend,dragonfly-hot-end,voron-hotend etc.

3Д Печатач Термистор 100k NTC 3950 со 1 Мерач на продолжен кабел Употреба на жица за Ender 3 V2 Pro CR10 и други 3D печатачи екструдер Hotend

Heater NTC thermistor: with M3 Thread Stud thermistor，Fast-Plug Connector Compatible with 3/3 V2/3 Neo/3 V2 Neo/3S/3 PRO/5/5

NTC100K Термисторски сензор за креативност 3 v2 Надградба 3x15mm 3950 Компатибилен со термистор

Radial Leaded Resin Coated NTC Thermistor Features
High measurement accuracy.
Tight tolerance on resistance and Beta value.
Fast response, small dimension.
Can operate in long time stability.
Nominal resistance @25C can be from R25 1kΩ–1000kΩ.
Typical resistance at 25C R25 1k ohm, 2k ohm, 2252 ohm, 3k ohm, 4.7k ohm, 5k ohm, 6.8k ohm, 10k ohm, 15k ohm, 20k ohm, 30k ohm, 40k ohm, 47k ohm, 50k ohm, 100k ohm, 150k ohm, 1000k ohm, итн.
Dissipation factor: ≥3.0 mW/C in still air.
Thermal time constant: ≤12 seconds in still air.
Оперативен опсег на температура: -45C — +125C.

Notes：□ in the part number for filling in resistance tolerance,
optional for ±1%(Ф), ±2%(Г), ±3%(Х), or ±5%(Ј).