Sensor suhu NTC dengan Jalur Koneksi Terminal Overmolding

Probe sensor suhu NTC dengan Konektor Overmolding (JST, Moleks, RJ11, RJ12, RJ45, RJ50, XH, SM, PH, Steker penerbangan, blok terminal, 5557, Terminal cepat, jack audio, dll.). Kepala sensor terbuat dari bahan TPE, Yang memiliki daya rekat dan penyegelan yang baik. The sensor of Waterproof TPE plastic overmolding NTC thermistor is a kind of waterproof sensor solution. Kepala sensor terbuat dari bahan TPE, Yang memiliki daya rekat dan penyegelan yang baik. Softness and flexibility make this product widely used in a variety of applications.

The flexible and wide temperature range cable makes this type of probe particularly advantageous for cold detection applications.

The specifications of the sensor and the length of the cable can be customized according to requirements.

Waterproof NTC sensor TPE Overmolding water temperature measurement

TPE Overmolding10K 3950 kabel sensor suhu tangki air Dengan colokan audio 6.35mm

Sensor NTC baja tahan karat dengan konektor TPE Overmolding

Subject	Spesifikasi	More options
Sensor	NTC 10KΩ	NTC 10K, NTC 50KΩ, NTC 100KΩ, PT100, PT1000, DS18B20, dll..
Kabel	TPE cable	PVC cable, PU cable, silicone cable, dll..
Konektor	Nothing	JST, Moleks, RJ11, RJ12, RJ45, RJ50, XH, SM, PH, Steker penerbangan, blok terminal, 5557, Terminal cepat, jack audio, dll..
Precision	1%	1,5%, 2%, 2,5%, 3%, dll..
IP class	IP68	IP65, IP66, IP68, dll..

Waterproof NTC, PT100, DS18B20 temperature sensors can be used in many places, such as soil temperature detection, hot water tank temperature control, dll.. The waterproof temperature sensor is a TPE Plastic Overmolding temperature sensor. This sensor can play a great role in measuring the temperature at a distance and in a humid environment. It is suitable for temperature detection in freezing and refrigeration environments such as refrigerators, indoor and electromechanical equipment temperature detection, soil temperature detection, hot water tank temperature control and other scenarios. It can be used with Arduino, mikro:bit and other main controllers. It not only supports mind+ and makecode graphical programming, but also supports programming-free functions.

The waterproof temperature sensor can be used with Arduino, Micro:bit and other main controllers. Saat menggunakan, a pull-up resistor must be connected and used with a pluggable sensor adapter.
Connect the circuit as shown in the figure below. Setelah dinyalakan, put the probe of the waterproof temperature sensor into the object to be measured, and the temperature value of the measured object can be directly read through the display module. The temperature sensing range of the waterproof temperature sensor is between -55℃~+125℃, and the temperature display range is -10°C+85°C (error ±0.5°C).

Catatan: Although the product can work normally at 125°C. Namun, since the cable is made of polyvinyl chloride (PVC) material and is not as heat-resistant as the sensor, we recommend not placing it in a place where the temperature is higher than 100°C.

Principle Introduction
The probe of the TPE Plastic Overmolding sensor uses a thermistor and is potted with a sealant with high thermal conductivity. The high sensitivity and minimal temperature delay of the sensor are guaranteed, and each pin of the chip itself is separated by a heat shrink tube to prevent short circuits. It is packaged with high-quality stainless steel tubes to achieve waterproof, moisture-proof and rust-proof functions.

Probe Sensor Pencairan Sensor Suhu Pembekuan

Keterangan

JENIS:	TPE Plastic Overmolding sensor	B25/50:	3950K, 3977K, 3435K
Kepala Sensor:	Wahai Cincin, Garpu Logam, Tabung yang Disuntik, NPT, M16, Tabung Baja tahan karat	Kabel:	CL2 PT4,#24 2466,#28 1332
Penggunaan:	Sensor Pencairan Kulkas, Pemanas Air Instan, pemanas air, AC, lemari es, air mancur, kompor induksi, pembuat kopi	hal (dinilai Kekuatan):	50mw
Menyorot:	EPCOS / AVX / SEMITEK / SUBARA / MITSUBISHI / Sensor termistor OHIZUMI NTC, TPE Plastic Overmolding sensor

Custom TPE Plastic Overmolding ntc temperature sensor Wire 0.5M~10M Theory Signal Output Origin.

Nama Spesifikasi	Cakupan	Kondisi Deteksi
R25(nilai resistansi nominal)	1k, 2k, 2.7k, 3k, 5k, 10k, 15k, 20k, 30k, 40k, 47k, 50k, 100k, 200k (EPCOS / AVX / SEMITEK / SUBARA / MITSUBISHI / Termistor OHIZUMI NTC)	Suhu konstan 25℃±0,05℃
R25 Varians yang diijinkan(%)	±1,±2, ±3, ±5, ±10	Suhu konstan 25℃±0,05℃
B25/50 atau B25/85(koefisien material)(indeks sensitivitas termal)	2500~5000K	Suhu konstan 25℃±0,05℃ Suhu konstan 85℃±0,05℃
B25/50 Nilai variansi yang diperbolehkan(%)	±1,±2	Suhu konstan 25℃±0,05℃ Suhu konstan 50℃±0,05℃
∫(koefisien disipasi)	≥0,8mw/℃	Statis di udara
T(konstanta waktu termal)	≤25S	Statis di udara
Menghadapi(Suhu kerja)	-30℃~+120℃
hal (daya terukur)	50mw	dalam suhu kerja
Kasus dan kepala		Kepala garpu, Wahai kepala cincin,tetes kepala air, Kasus logam, Kotak tembaga berulir, kepala injeksi, Tabung Baja tahan karat, atau sesuai dengan gambar klien
Kawat timah		#24 30# 2651, UL4411 28#, konduktor kabel ganda dan sebagainya, atau sesuai permintaan klien.
Terminal		Dapat dipaku sesuai dengan kebutuhan berbagai terminal

Layanan
1. Pertanyaan Anda akan dijawab dalam 24 jam;
2. Staf yang terlatih dan berpengalaman selalu siap melayani Anda.
3. Produk berdesain unik dan banyak produk cetakan pribadi menunggu pilihan Anda.
4. Lindungi secara ketat informasi pribadi dan ide desain Anda.
FAQ

Q1. Bisakah saya memesan sampel untuk NTC, PT100,PT1000, RTS, dan SENSOR Ds18b20?
A: Ya, kami menerima pesanan sampel untuk menguji dan memeriksa kualitas. Sampel campuran dapat diterima.