Rakitan Probe sensor Termistor Kustom China untuk kontrol suhu

An NTC thermistor is a temperature sensor that uses the resistance properties of ceramic/metal composites to measure the temperature. Our full spectrum NTC thermistor is a resistance thermometer, or a resistor whose resistance is dependent on temperature. The term is a combination of “thermal” and “resistor”. It is made of metallic oxides, pressed into a bead, disk, or cylindrical shape and then encapsulated with an impermeable material such as epoxy or glass. Produsen Probe sensor Resistor Kelas Atas — YAXUN berspesialisasi dalam termistor yang menampilkan sensitivitas suhu dan memenuhi syarat AEC-Q200. TCTR – Termistor Film Tebal NTC. 47-1.6MΩ. Toleransi paling ketat 1%. Nilai B 2410K – 4800K.
Sensor Suhu Termistor — Termistor Linier Berbasis Silikon Dengan Biaya dan Ukuran Yang Sama Dengan Termistor NTC Tradisional. Mencapai Keandalan Sistem Akurasi Tinggi Dengan Termistor Linier Terkecil di Industri.
Field-proven thermistor level-sensing technology with NPT mounting threads;
SP-M models temperature sensor are designed for use with ST-15 Control Monitors Electrical appliances, mobil, aviation, small household appliances, toys;
Typical uses include storage tanks, double-containment piping trenches, and double-wall storage tank interstitial space monitoring;
Years of dependable, virtually maintenance-free operation;
Sensors can be easily extended to desired length at installation site using a 3/8” x 3/8” coupler and the required length of 3/8” NPT pipe.

Ender 3 Thermistor Sensor, Upgrade HT-NTC100K 3D Printer Thermistor Sensor: Thermistor temperature sensor. Metal head diameter: 3 mm, head length: 15 mm,cable wire length: 1 meter,konektor: XH2.54 2PIN, （Suitable for heating blocks with holes of 3 mm*15 mm-3 mm*20 mm）;
Widly Compatibility: Product recommended operating temperature -50 °C ~ +280 ° C., can replace the cartridge K-type thermocouple temperature sensor. Compatible with the heatblocks with 3 mm hole,seperti: V6 Volcano PT100 type heated block, dll.;
Sensors is accurate: The best feature was the flexible and heat shielded probe leads to the copper sensor. Unlike the other with a nickel plated probe/heat shrink, this can be fitted in very tight spots without worry. Be sure you redo your PID calibration;
Long Service Life: Compared with the same type that are insulated with ordinary heat shrinkable tubes, ours uses glass fiber with a temp resistance of 400C degrees for insulation to avoid the possibility of thermal short circuit during high temp work;
Fit ALL-METAL HOTEND: Work for E3D-V6 Volcano PT100 Ender 3 series all-metal hotend such as spider-hotend,K1-red-Lizard-hotend,dragonfly-hot-end,voron-hotend etc.

3D Termistor Printer 100k NTC 3950 dengan 1 Penggunaan Kawat Kabel Perpanjangan Meter untuk Ender 3 V2 Pro CR10 dan Hotend ekstruder Printer 3D lainnya

Heater NTC thermistor: with M3 Thread Stud thermistor，Fast-Plug Connector Compatible with 3/3 V2/3 Neo/3 V2 Neo/3S/3 PRO/5/5

Sensor Termistor NTC100K untuk Creality 3 v2 Tingkatkan 3x15mm 3950 Kompatibel dengan termistor

Radial Leaded Resin Coated NTC Thermistor Features
Akurasi pengukuran tinggi.
Tight tolerance on resistance and Beta value.
Fast response, small dimension.
Can operate in long time stability.
Nominal resistance @25C can be from R25 1kΩ–1000kΩ.
Typical resistance at 25C R25 1k ohm, 2oke ohm, 2252 ohm, 3oke ohm, 4.7oke ohm, 5oke ohm, 6.8oke ohm, 10oke ohm, 15oke ohm, 20oke ohm, 30oke ohm, 40oke ohm, 47oke ohm, 50oke ohm, 100oke ohm, 150oke ohm, 1000oke ohm, dll..
Faktor disipasi: ≥3.0 mW/C in still air.
Konstanta waktu termal: ≤12 seconds in still air.
Kisaran suhu pengoperasian: -45C — +125C.

Notes：□ in the part number for filling in resistance tolerance,
optional for ±1%(F), ±2%(G), ±3%(H), or ±5%(J).