10Un fusible de temperatura de 250 V RY RH per a l'arròs, Ventilador elèctric

10A 250V RY RH thermal fuse before action:
The metal shell of the SF type overheat fuse contains a movable electrode, a spring and a thermistor. Spring B is installed in a compressed state, and the spring force is used to make lead A, movable electrode, metal shell and lead B conductive.

After the RY RH thermal fuse is activated:
When the ambient temperature exceeds the fuse action temperature, the heat transferred through the metal shell melts the thermistor particles, and springs A and B are both extended, but the elastic force in the A direction is large, forcing spring B to press toward the B side, thereby disconnecting lead A and the movable electrode to cut off the circuit.

2: Thermal circuit breaker (SM type)
The low melting point alloy is installed in the ceramic shell as a heat-sensitive material. Its cut-off current is 0.5A, 1Una, and 2A. It has the advantage of being directly installed at the temperature detection location.

Fusible tèrmic Sanyuan sèrie RY fusible de temperatura 250V 10A

quality Alloy Type 250V 10A, 15Una, 20A Square Thermal Fuses

10Una,20Una,16A 250 V RY RH Fusibles tèrmics

Principle:
Before action:
Lead A and lead B are connected to the circuit together with the fusible element. The outer surface of the rotator is covered with flux.
After operation:
The temperature of the fusible material rises with the rise of the ambient temperature, and it melts soon. Under the action of the flux and the surface tension of the fusible material, it instantly forms a ball, thereby cutting off the circuit.

4. Features and uses
1. Característiques:
a. Because of its small size, it is very sensitive to the ambient temperature.
b. Due to its airtight structure, the change caused by aging is very small, and it has a very high operating temperature.
c. It is a non-recovery type, and it will not recover even if the temperature drops after operation.
2. Uses:
jo. Cuines elèctriques, electric hot tables, electric carpets, kerosene fan heaters, warm air blowers.
jo. Planxes elèctrics, trouser presses, hot hair dryers, assecadors de cabells, rechargeable shavers.
III. Air conditioners, ventilating fans, rentadores, etc.
V. Refrigerators, color TVs, fluorescent lamps, etc.
V. Electric rice cookers, grills, cafeteres, electric money cookers.

Common installation methods include:
Welding, splicing, and welding
(1) Installation position: more than 5 mm from the fuse body.
(2) Do not allow the welding heat to cause the temperature to exceed the fuse action temperature during welding.
Solutions:
a. Clamp the tool or fixture near the shell to dissipate heat;
b. Shorten the operation time;
c. Reduce the welding temperature;
d. Weld away from the fuse body.
(3) Do not increase the resistance during splicing or welding.
If the resistance of the connection part is too large, abnormal heating will cause the fuse to operate when the power is turned on. Especially in splicing situations, the resistance will increase due to thermal cycles or temperature.
(4) Després de la instal·lació, do not pull, premsa, or twist the lead wire.
(5) Do not allow the resin-sealed lead wire to contact the fuse body. If contact is made, the current can be transmitted to the other end through the metal shell, and the purpose of cutting off the circuit cannot be achieved.
(6) The SF type cannot contact the metal part of the installation part.
(7) When crimping, the rear part cannot be loose, and copper crimping terminals are suitable.
(8) The installation location should be where the machine is prone to failure and generates the most abnormal heat.

Descripció del producte

DYE 250V 15A 16A Thermal Cutoff Fuse Thermal Cutout Link DF104S DF184S DF192S

Descripció del producte

The Thermal DF Series Thermal Cutoffs are single action devices that open when

a preset temperature is reached. They do not reset. The active component of a thermal

cutoff is an electrically insulated thermal pellet. This pellet holds a spring loaded

contact against a fixed contact under normal operating temperatures. (See Fig. 1)

When the preset temperature of the cutoff is reached, the pellet liquifies, the springs

relax, and the spring loaded contact is moved away from the fixed contact, opening the

circuit. The DF Series is the right choice for applications requiring an inexpensive

limit protector with 15A capability.

Característiques del producte

Corrent nominal: UL 250V 10A/16A, VDE 15A, CCC 15A

Avantatge: Operació d'un sol tret, estable i precís, compacte, durador i fiable per estructura de segell hermètic, excel·lentment sensible a la temperatura ambient.

Funció: Fusible tèrmic, Àmpliament utilitzat en electrodomèstics de corrent elèctric com a protecció de calor. Quan les temperatures superen el nivell de TF especificat, S'obriran els contactes elèctrics.

Aplicacions: Apte per a electrodomèstics, equips elèctrics industrials, equips d'ofimàtica, fotocopiadores de paper normal, transformadors, motors, etc.

Especificació

(Fusible tèrmic SEFUSE SF-E, tall tèrmic, enllaç tèrmic)

Tolerància a la temperatura d'obertura: TF+0°C/-5°C

Classificació de temperatura (Tf):Temperatura nominal d'obertura

Temperatura de manteniment (Th):Temperatura màxima mesurada a l'extrem del cas del tall tèrmic a la qual es pot mantenir el tall tèrmic durant un període de 168 hores sense obrir.

Temperatura màxima (Tm):La temperatura màxima a la qual es pot mantenir un tall tèrmic durant 10 minuts com a circuit obert i després es pot mantenir a una tensió nominal doble durant un període de 2 minuts durant els quals no es veuran afectades les seves propietats mecàniques i elèctriques