NTC temperatuursensor met Overmolding Terminal Connection Line

NTC-temperatuursensorsonde met Overmolding Connector (JST, Moleks, RJ11, RJ12, RJ45, RJ50, XH, SM, PH, Lugvaart prop, eindblokke, 5557, Faston-terminaal, oudio-aansluiting, ens). Die sensorkop is gemaak van TPE-materiaal, wat 'n goeie adhesie en verseëling het. The sensor of Waterproof TPE plastic overmolding NTC thermistor is a kind of waterproof sensor solution. Die sensorkop is gemaak van TPE-materiaal, wat 'n goeie adhesie en verseëling het. Softness and flexibility make this product widely used in a variety of applications.

The flexible and wide temperature range cable makes this type of probe particularly advantageous for cold detection applications.

The specifications of the sensor and the length of the cable can be customized according to requirements.

Waterproof NTC sensor TPE Overmolding water temperature measurement

TPE Overmolding10K 3950 watertenk temperatuursensor kabel Met 6,35 mm oudioprop

Vlekvrye staal NTC sensor met TPE Overmolding koppelstuk

Subject	Spesifikasie	More options
Sensor	NTC 10KΩ	NTC 10K, NTC 50KΩ, NTC 100KΩ, PT100, PT1000, DS18B20, ens.
Kabel	TPE cable	PVC cable, PU cable, silikoonkabel, ens.
Koppelaar	Nothing	JST, Moleks, RJ11, RJ12, RJ45, RJ50, XH, SM, PH, Lugvaart prop, eindblokke, 5557, Faston-terminaal, oudio-aansluiting, ens.
Precision	1%	1,5%, 2%, 2,5%, 3%, ens.
IP class	IP68	IP65, IP66, IP68, ens.

Waterproof NTC, PT100, DS18B20 temperature sensors can be used in many places, such as soil temperature detection, hot water tank temperature control, ens. The waterproof temperature sensor is a TPE Plastic Overmolding temperature sensor. This sensor can play a great role in measuring the temperature at a distance and in a humid environment. It is suitable for temperature detection in freezing and refrigeration environments such as refrigerators, indoor and electromechanical equipment temperature detection, soil temperature detection, hot water tank temperature control and other scenarios. It can be used with Arduino, micro:bit and other main controllers. It not only supports mind+ and makecode graphical programming, but also supports programming-free functions.

The waterproof temperature sensor can be used with Arduino, Micro:bit and other main controllers. By gebruik, a pull-up resistor must be connected and used with a pluggable sensor adapter.
Connect the circuit as shown in the figure below. After powering on, put the probe of the waterproof temperature sensor into the object to be measured, and the temperature value of the measured object can be directly read through the display module. The temperature sensing range of the waterproof temperature sensor is between -55℃~+125℃, and the temperature display range is -10°C+85°C (error ±0.5°C).

Note: Although the product can work normally at 125°C. Egter, since the cable is made of polyvinyl chloride (PVC) material and is not as heat-resistant as the sensor, we recommend not placing it in a place where the temperature is higher than 100°C.

Principle Introduction
The probe of the TPE Plastic Overmolding sensor uses a thermistor and is potted with a sealant with high thermal conductivity. The high sensitivity and minimal temperature delay of the sensor are guaranteed, and each pin of the chip itself is separated by a heat shrink tube to prevent short circuits. It is packaged with high-quality stainless steel tubes to achieve waterproof, moisture-proof and rust-proof functions.

Vriestemperatuursensor Ontdooisensorsonde

Beskrywing

TIPE:	TPE Plastic Overmolding sensor	B25/50:	3950K, 3977K, 3435K
Sensorkop:	O Ring, Vurk metaal, Ingespuite buis, NPT, M16, vlekvrye staal buis	Draad:	CL2 PT4, #24 2466,#28 1332
Gebruik:	Yskas ontdooi sensor, Kitswaterverwarmers, waterverwarmer, lugversorger, yskas, water fontein, induksie kookplaat, koffiemaker	Pn (gegradeerde krag):	50mw
Hoë lig:	EPCOS / AVX / SEMITEC /SUBARA / MITSUBISHI / OHIZUMI NTC termistorsensor, TPE Plastic Overmolding sensor

Custom TPE Plastic Overmolding ntc temperature sensor Wire 0.5M~10M Theory Signal Output Origin.

Spesifikasie Naam	Omvang	Opsporingstoestand
R25(nominale weerstandswaarde)	1k, 2k, 2.7k, 3k, 5k, 10k, 15k, 20k, 30k, 40k, 47k, 50k, 100k, 200k (EPCOS / AVX / SEMITEC /SUBARA / MITSUBISHI / OHIZUMI NTC termistor)	Konstante temperatuur 25℃±0.05℃
R25 Toelaatbare afwyking(%)	±1,±2, ±3, ±5, ±10	Konstante temperatuur 25℃±0.05℃
B25/50 of B25/85(materiaal koëffisiënt)(termiese sensitiwiteitsindeks)	2500~5000K	Konstante temperatuur 25℃±0.05℃ Konstante temperatuur 85℃±0.05℃
B25/50 Waarde toelaatbare afwyking(%)	±1,±2	Konstante temperatuur 25℃±0.05℃ Konstante temperatuur 50℃±0.05℃
∫(dissipasiekoëffisiënt)	≥0.8mw/℃	Staties in die lug
T(termiese tydkonstante)	≤25S	Staties in die lug
Gesig(Werkstemperatuur)	-30℃~+120℃
Pn (gegradeerde krag)	50mw	binne werkstemperatuur
Kas en kop		Vurk kop, O ringkop,druppels water kop, Metaalkas, Draad koper omhulsel, inspuitkop, vlekvrye staal buis, of volgens kliënt se tekening
Leidraad		#24 30# 2651, UL4411 28#, dubbelbedraad geleier en so aan, of volgens kliënt se versoek.
Terminale		Kan vasgenael word volgens die vereistes van verskeie terminale

Dienste
1. Jou navraag sal binne beantwoord word 24 ure;
2. Goed opgeleide en ervare personeel is altyd tot jou diens.
3. Unieke ontwerpprodukte en baie private vormprodukte wag op u keuse.
4. Beskerm u privaat inligting en u ontwerpidees streng.
Vrae

V1. Kan ek 'n voorbeeldbestelling vir NTC kry, PT100, PT1000, RT's, en Ds18b20 SENSOR?
N: Ja, ons verwelkom voorbeeldbestelling om kwaliteit te toets en na te gaan. Gemengde monsters is aanvaarbaar.