Mikro mediese radiofrekwensie ablasie elektrode temperatuur sensor

Medical surface temperature sensor
Product introduction:
φ0.30mm PI-buis verpakte mediese temperatuursensor. Hierdie produk is 'n miniatuur mediese radiofrekwensie ablasie elektrode temperatuur sensor. Die produk gebruik 'n poliimiedbuis met 'n buitenste deursnee van Maxφ0.30mm om epoksiehars in te kapsuleer, en die looddraad gebruik 'n geëmailleerde draad met 'n buitenste deursnee van 0,05 mm. Die weerstandswaarde van die miniatuur termistorsensor word een vir een gekalibreer.

Medical surface temperature sensor, volledige produkmodelle, betroubare kwaliteit. 1K tot 680K weerstand opsioneel, dienslewe tot 10 jare. Mediese-graad temperatuursensor, motor sensor, huistoestelsensorskyfie gebruik hoë-presisieskyfie, die reaksietyd kan bereik 0.5 sekondes.

The chip is epoxy encapsulated and can be equipped with a 6.3mm mono audio plug (other plugs can also be equipped according to customer requirements). The measurement temperature tolerance is within (25℃ ~ 45 ℃)±0.1℃, compatible with YSI400 series temperature sensors.

Produk kenmerke
PI maxφ0.30mm
Enameled wire OD0.05mm
Vinnige reaksie
Bedryfstemperatuurreeks: 0℃~100℃

Product application
Monitoring ablation temperature detection

Product structure and size (Eenheid: mm)

Seleksie van mediese temperatuursensor

Mediese temperatuursensor

Temperatuursensor vir die monitering van ablasietemperatuuropsporing

Serial number	Name	Material specification	Quantity	Opmerkings
1	Chip	NTC thermistor chip	1	/
2	Probe	Polyimide tube outer diameter Maxφ0.35mm, Maxφ0.5, Maxφ0.6, Maxφ1.0	1	Gray
3	Draad	The lead wire uses enameled wire with outer diameter OD0.052mm, OD0.12 2, OD0.2 *2	1	Gray
4	Plug	6.3MP-φ6.3*31-50 mono audio plug	1	Gray

Packing quantity: 1 pcs/packing

2.252kΩ or 10kΩ RT temperature resistance table for medical sensors

Monitoring ablation temperature detection temperature sensor product structure and size

Voorsorgmaatreëls
— Purpose of this product: temperature measurement and control.
— Control the energy dissipation generated by the current flowing through the chip within the required range to avoid measurement errors caused by self-heating of the component.
— If the shrink sleeve is heated at the temperature sensing head, the air outlet of the welding gun should be more than 30mm away from the temperature sensing head to avoid excessive thermal shock of the resistor body caused by high temperature, resulting in resistance drift.
— Storage temperature 0℃～50℃, humidity 30%~80%RH; avoid storage in an environment with corrosive gas or direct sunlight; after opening the package, it needs to be resealed for storage.
— In view of the structural characteristics of epoxy components, users should avoid excessive stretching and bending forces from the lead wires on the component encapsulation head when using it. If the lead wire needs to be bent, the bending point or force point should be controlled on the lead wire 6mm below the encapsulation head to avoid pulling the chip, causing resistance drift or even open circuit, especially when the component is heated.

Dienste
1. Jou navraag sal binne beantwoord word 24 ure;
2. Goed opgeleide en ervare personeel is altyd tot jou diens.
3. Unieke ontwerpprodukte en baie private vormprodukte wag op u keuse.
4. Beskerm u privaat inligting en u ontwerpidees streng.

Vrae

V1. Kan ek 'n voorbeeldbestelling vir NTC kry, PT100, PT1000, RT's, en Ds18b20 SENSOR?
N: Ja, ons verwelkom voorbeeldbestelling om kwaliteit te toets en na te gaan. Gemengde monsters is aanvaarbaar.